Hermle Quartz Movement Replacement

Description: Hermle Quartz Movement Replacement Hermle Quartz Clock Movement Replacement Replacement movements for the German made Hermle quartz, . These chiming units take two C-cell batteries and play two different songs. Well made quartz movements that last for a long time. The old units seem to give up the ghost during daylight savings when they do die. Hermle Quartz Clock Movement Removal Instructions Hermle quartz clock movement ment. These chiming units take two C-cell batteries and play two different songs. These are well made quartz movements that last for a long time. Most of the old units seem to give up the ghost during the change of daylight savings when they do finally stop working. Hermle Quartz Clock Movement Replacement Assistance = Dial Thickness 1/16 inch thick 3/16 inch thick 5/16 inch thick 9/16 inch thick 3/4 inch thick Needs this Post Size 3/16" 5/16" 7/16" 11/16" 15/16" New Quartz Clock Movement Particulars About the movement The MSO quartz movement has step motion timekeeping accuracy and a time setting knob on the back of the unit which is useful if the hands are not easily accessible from the front. Additionally, there is a knob on the back to control the volume. The base unit is 4 5/8W (117mm) x 5 1/4T (149mm) x 1 1/4D (32mm) without the hand shaft. It would require 4 3/4W (121mm) x 5 7/8T (133mm) x 1 1/2D (38mm) area to run right. Although this is a pendulum unit it can run with or without the pendulum. The pendulum motion does not have anything to do with the timekeeping on this unit. Another thing to keep in mind is that the clock hands are sold separately. About the chimes This unit will play either Westminster or Ave Maria with premium sound quality. It is quite possible this is the only quartz movement that plays Ave Maria on the market at this point. Additionally, it also has the ability to play the chime every quarter hour or only on the top of the hour. Please note that the clock chime may take an hour to correct itself, when using the hand setting knob. Of course the sound is premium as it has a larger external speaker that mounts anywhere in the clock case with just two small wood screws. The strike count at the top of the hour can be set by the button on the back of the unit. It will advance the strike count one hour each time the button is pressed. Doing this will not move the hands. About the hands The MSO quartz unit uses any of the low torque quartz hands that Clockworks has to offer. If replacing a Hermle quartz unit, new hands also need to be bought for the new unit as the old ones will no longer fit. It is possible to use a needle file to make the old hands fit the new unit. However it is best to just get the new hands with it just in case. This unit will take a second hand but it is optional. Clockworks offers the hands for this unit below. About the pendulum Overall, the pendulum that is offered is 16 inches. However, it has segments at every inch, so measure what is needed, bend it and snap it off. Similarly, the pendulum has three bob diameter options to choose from. The bob is the round disk at the bottom of the pendulum rod. Please note, although this is a pendulum unit, it can run with or without the pendulum. If the pendulum is not needed lock the pendulum swinger to one side. The pendulum and bob are sold separately. About the post lengths The movement has threads on the post and comes in two lengths. This is the fat part with the threads that takes the hex nut. The length of the threads is what we measure to get the post length. Do not count the part that the hands go onto in the measurement. The post lengths available for this unit is either 5/16 long or 9/16 long. The posts are all 5/16 wide, and fit into a ⅜ dial hole. Hermle Quartz Clock Movement Removal Instructions Getting to the dial and hands There are many clock case designs and styles so this is difficult to give an exact procedure. Sometimes it is very easy to get to the dial and hands. Other times the dial has glass over it and may require to figure out how the clock case was put together. Of course, may have to remove some screws, or if there is a bezel the bezel tabs may need to be bent to get it to come off. Once at the point where the hands can be removed and also the back of the quartz unit, good to start replacing the unit. Removing the clock hands If there is a second hand on the clock, grab it with fingers and pull it straight off of the clock. Hold the minute hand still as turning the nut to the left with needle nose pliers to remove the nut and the hand. Next is the hour hand, this is only a friction fit, twist and pull off. Removing a Hermle Quartz Movement First thing to do when replacing a Hermle quartz clock movement is to get the old unit out of the clock case. Remove the hands and then the nut with the double slots under the hands. This nut turns to the left to unscrew, but it is not easy to do sometimes. A clock maker will have a special tool for these units only, but the customer is left to use two flat screwdrivers to do it. It is easy to slip and scratch the dial when doing this. Use a flathead screwdriver on both sides of the nut and turn them both at once to the left. The nut will come off and the movement will fall out from the back side. New Quartz Clock Movement Installation Instructions Place hanger on post (optional) Place black washer on post (optional) Put post through the clock dial face Slide the brass washer onto the post of the movement that is sticking out of the clock dial face Put hex nut on post and tighten to hold movement to the back of the clock face. Quartz hands installation Push hour hand onto the post as far down as it will go without touching the clock face. Put the minute hand on the post If using a second hand, skip to step 9 otherwise screw the cap nut on and it is done If using a second hand, screw the small nut on top of minute hand then push the second hand onto the pin in the center. Now done installing the brand new quartz clock movement ! Features Westminster or Ave Maria Quarterly or Hourly Chime Volume Control Second Hand Option Pendulum Option Takes Two C Cell Batteries Instructions Connect the speaker wire. Install two C-cell batteries, plus side up. Turn set knob until it strikes the hours. Put the hands on, pointing to that hour. Never turn the minute hand backwards. Choose the chime options. Making it chime on time Make the clock chime and count how many times it strikes. Then take off the hands and put them back on to display the number of strikes. In other words, if there were 3 strikes put the hands on to point to 3 o'clock. If the clock minute hand will not point exactly to the 12, do this. Find the circle setting knob on the back of the movement and hold this still with the fingers so it will not move. At the same time, point the minute hand to the 12. Then let go of both. Threaded Post LengthPrice5/16" Threads for 3/16" Thick Dials96.00 Shipping Shipping cost:Clockworks products are shipped out within a day or two of purchase. Our team works hard shipping M-F. Delivery time:Handling time is 1-2 days then once your product ships it should take at the most 5 business days to get to you. Payment We accept the following payment methods: Paypal Debit Credit Please contact us if you have any questions.

Price: 96 USD

Location: Huntington, Massachusetts

End Time: 2023-11-29T13:09:13.000Z

Shipping Cost: 6 USD